Search by number : 130161
Article Availability Price
BE TURBO 130161 Substitutes
Charger, charging (supercharged/turbocharged)
Trade numbers : 775806-5016S, 830724-5002S
Charge Type: Exhaust TurbochargerQuality: Original
CEVAM 130161 Substitutes
Hydraulic Pump, steering
for steering manufacturer: SAGINAWOperating Mode: HydraulicPulleys: without belt pulley
KLARIUS 130161 Substitutes
Exhaust Pipe
Fitting Position: FrontHeight: 180mmLength: 870mmWeight: 2,9kgWidth: 395mm
MAXGEAR 13-0161 Substitutes
Ignition Coil
Trade numbers : MG-9024
Ignition Coil: Connector Type SAENumber of pins: 2-pin connector
METELLI 13-0161 Substitutes
Bellow Kit, drive shaft
Inner Diameter: 26mmLength: 106mmMaterial: RubberOuter Diameter: 93mmThread Size: M22x1.5
STATIM 130.161 Substitutes
Clutch Kit
Clutch: Conversion from dual-mass flywheel to single-mass flywheelClutch Equipment: cover, discClutch Equipment: CSCClutch Equipment: rigid flyw., screwsØ: 228mmHub Profile: 18,3 x 20,8 - 18N
3RG 95501 Substitutes
Sensor, washer fluid level
Replaced numbers : 95587, 95588, 95594, 95583, 95584, 95597, 95586
A.Z. Meisterteile AZMT-49-046-1134 Substitutes
Ignition Coil
Connector type: Spark SpringNumber of connectors: 1Number of pins: 2-pin connectorVoltage: 12V
ABAKUS 122-01-137 Substitutes
Ignition Coil
Ignition Coil: Connector Type SAENumber of pins: 2-pin connectorVoltage: 12V
AUTOGAMMA 100762 Substitutes
Radiator, engine cooling
Core Depth: 32mmCore Length: 330mmCore Width: 358mmHeight: 330mmThickness: 32mmWidth: 358mm
BLUE PRINT ADM51416 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,260kg
BLUE PRINT ADJ139111 Substitutes
Water Pump, engine cooling
Replaced numbers : ADH29137
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
BORG & BECK BWP1578 Substitutes
Water Pump, engine cooling
Replaced numbers : BWP1800
Bolt Ø: 65mmSupplementary Article/Supplementary Info: with gaskets/seals
BREMI 20313 Substitutes
Ignition Coil
Replaced numbers : 15043
Ignition Coil: Connector Type SAEIgnition Coil: Flush-Fitting Pencil Ignition CoilsNumber of pins: 2-pin connectorVoltage: 12V
BSG BSG 65-705-016 Substitutes
Bellow Kit, drive shaft
Trade numbers : 65705016, BSG 65705016, BSG65705016
Component Number: BSG 65-705-016Fitting Position: Front AxleFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: Rubber
BUGATTI PA5204 Substitutes
Water Pump, engine cooling
Impeller Ø: 66mmNumber of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: MetalWater Pump Type: for v-ribbed belt use
BUGATTI PA10274 Substitutes
Water Pump, engine cooling
Impeller Ø: 64,8mmNumber of blades/vanes: 8Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWater Pump Pulley Ø: 62,3mmWater Pump Type: for timing belt drive
CEVAM 1147 Substitutes
Bellow Kit, drive shaft
Inner Diameter 1: 22mmInner Diameter 2: 78mmLength: 103mmMaterial: NBR (nitrile butadiene rubber)
CIFAM 613-161 Substitutes
Bellow Kit, drive shaft
Inner Diameter: 26mmLength: 106mmMaterial: RubberOuter Diameter: 93mmThread Size: M22x1.5
DENCKERMANN E100052 Substitutes
Ignition Coil
Ignition Coil: Connector Type SAENumber of pins: 2-pin connector
DIEDERICHS DCT1140 Substitutes
Dryer, air conditioning
Quality: DIEDERICHS ClimateSupplementary Article/Info 2: with pressure switch
DIEDERICHS 8430859 Substitutes
Rear Window
Trade numbers : 2722BCLVRU1J
Fitting Position: RightGlass: Clear glassGlass: not heatableVehicle Equipment: for vehicles with raised roof
DR!VE+ DP2310.10.081 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater Pump Type: for v-ribbed belt use
DR!VE+ DP2310.10.020 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalWater Pump Type: for timing belt drive
ESEN SKV 17SKV640 Substitutes
Sensor, washer fluid level
Colour: BlackCombi Switch Function: Reed ContactHeight: 88,6mmNumber of pins: 2-pin connectorRated Power: 0,25WRated Voltage: 8VSupplementary Article/Info 2: with seal ringWarranty: 3 years warranty
ESEN SKV 03SKV122 Substitutes
Ignition Coil
Ignition Coil: incl. spark plug connectorNumber of pins: 2-pin connectorOperating Mode: ElectricVoltage: 12VWarranty: 4 years warrantyWeight: 0,24kg
FEBI BILSTEIN 02717 Substitutes
Bellow Kit, drive shaft
Fitting Position: Front AxleFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,209kg
FEBI BILSTEIN 03172 Substitutes
Bellow, drive shaft
Fitting Position: Front Axle LeftFitting Position: Front Axle RightFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,088kg
FEBI BILSTEIN 09699 Substitutes
Cable Pull, clutch control
Inner Length: 234mmLeft-/right-hand drive vehicles: for left-hand drive vehiclesOuter Length: 975mmWeight: 0,2kg
FEBI BILSTEIN 31143 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,200kg
FEBI BILSTEIN 109555 Substitutes
Water Pump, engine cooling
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
FEBI BILSTEIN 03288 Substitutes
Bellow, drive shaft
Replaced numbers : 03172
Inner Diameter 1: 22mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,074kg
FEBI BILSTEIN 28489 Substitutes
Sensor, washer fluid level
Length: 88,62mmOuter Diameter: 15,79mmWeight: 0,016kg
FIRST LINE FWP1578 Substitutes
Water Pump, engine cooling
Replaced numbers : FWP1800
Bolt Ø: 65mmSupplementary Article/Supplementary Info: with gaskets/seals
FRIGAIR 0204.2032 Substitutes
Radiator, engine cooling
Trade numbers : 2204.0032
Core Depth: 28mmCore Dimensions: 1000 x 414 x 28 mmCore Length: 1000mmCore Width: 414mmMaterial: AluminiumMaterial: Plastic
GK 980735 Substitutes
Water Pump, engine cooling
Replaced numbers : 982798
Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
GK 981049 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: Incl. Gasket Set
GRAF PA562 Substitutes
Water Pump, engine cooling
Impeller Ø: 66mmNumber of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: MetalWater Pump Type: for v-ribbed belt use
GRAF PA325 Substitutes
Water Pump, engine cooling
Impeller Ø: 64,8mmNumber of blades/vanes: 8Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWater Pump Pulley Ø: 62,3mmWater Pump Type: for timing belt drive
HEPU P398 Substitutes
Water Pump, engine cooling
Replaced numbers : P798
Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
HEPU P049 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
HERTH+BUSS JAKOPARTS J1514033 Substitutes
Water Pump, engine cooling
Number of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
KAMOKA 7120139 Substitutes
Ignition Coil
Ignition Coil: Connector Type SAENumber of pins: 2-pin connector
KWP 10562 Substitutes
Water Pump, engine cooling
Impeller Ø: 66mmNumber of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: MetalWater Pump Type: for v-ribbed belt use
KWP 10325 Substitutes
Water Pump, engine cooling
Impeller Ø: 64,8mmNumber of blades/vanes: 8Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWater Pump Pulley Ø: 62,3mmWater Pump Type: for timing belt drive
LIZARTE 81.10.26.053 Substitutes
Compressor, air conditioning
Colour: GreyComponent Number: 7422Compressor ID: 709/7H15Manufacturer Restriction: SANDENNumber of ribs: 2Oil Fill Quantity: 190mlRated Voltage: 12VWarranty: 2 years warranty
L?BRO 300393 Substitutes
Bellow Kit, drive shaft
Bellows Material: NBR (nitrile butadiene rubber)Height: 103mmInner Diameter 1: 22mmInner Diameter 2: 78mmSupplementary Article/Info 2: with nutThread Size: M22x1.5
LPR WP0156 Substitutes
Water Pump, engine cooling
Trade numbers : WP0156
Impeller Ø: 85,5mmOperating Mode: MechanicalWater Pump Type: for v-ribbed belt use
MAGNETI MARELLI 350981707000 Substitutes
Water Pump, engine cooling
Trade numbers : 350981707000, 81707
MAXGEAR 32-1849 Substitutes
Cable Pull, clutch control
Left-/right-hand drive vehicles: for left-hand drive vehiclesLength 1: 975mmLength 2: 234mm
MEC-DIESEL 53101833 Substitutes
Charger, charging (supercharged/turbocharged)
Charge Type: Exhaust Turbochargerfor turbocharger (art. no.): GTB3576KLNRVNumber of Cylinders: 6
METELLI 24-0562 Substitutes
Water Pump, engine cooling
Impeller Ø: 66mmNumber of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: MetalWater Pump Type: for v-ribbed belt use
METELLI 24-0325 Substitutes
Water Pump, engine cooling
Impeller Ø: 64,8mmNumber of blades/vanes: 8Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWater Pump Pulley Ø: 62,3mmWater Pump Type: for timing belt drive
MTR 12161015 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
MTR 3735BCLVRU1J Substitutes
Rear Window
Fitting Position: Right RearFitting Position: Vehicle rear windowGlass: Clear glassGlass: not heatable
NTY CPW-HD-031 Substitutes
Water Pump, engine cooling
Fabrication Number: CPW-HD-031Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
OPEN PARTS SJK7228.00 Substitutes
Bellow Kit, drive shaft
Fitting Position: Front AxleFitting Position: Wheel SideInner Diameter 1: 21mmInner Diameter 2: 76mmLength: 103mm
OPEN PARTS WAP8181.00 Substitutes
Water Pump, engine cooling
Distance from belt pulley to pump: 57,7mmHeight: 80mmImpeller Ø: 66,5mmWater Pump Pulley Ø: 28mm
PILKINGTON 420002418 Substitutes
Rear Window
Article number of recommended accessories: 250000232Article number of recommended accessories: 250000233Fitting Position: RightGlass: Clear glassGlass: not heatableVehicle Equipment: for vehicles with raised roof
PILKINGTON 420002417 Substitutes
Rear Window
Article number of recommended accessories: 250000232Article number of recommended accessories: 250000233Glass: Clear glassGlass: Heatable
PILKINGTON 420001336 Substitutes
Rear Window
Replaced numbers : 420001340
Article number of recommended accessories: 250000232Article number of recommended accessories: 250000233Fitting Position: LeftGlass: Clear glassGlass: not heatable
RIDEX 689C0034 Substitutes
Ignition Coil
Coil Ignition System: Full Electronic Ignition (FI)Ignition Coil: Flush-Fitting Pencil Ignition CoilsIgnition Coil: incl. spark plug connectorNumber of mounting bores: 1Number of pins: 2-pin connectorOperating Voltage: 12V
RUVILLE 56512P Substitutes
Water Pump, engine cooling
Belt Pulley Ø: 68mmNumber of Gaskets/Seals/Seal Rings: 1Number of Teeth: 21Operating Mode: MechanicalSeal Material: Rubber
Saleri SIL PA512P Substitutes
Water Pump, engine cooling
Belt Pulley Ø: 68mmNumber of Gaskets/Seals/Seal Rings: 1Number of Teeth: 21Operating Mode: MechanicalSeal Material: Rubber
SAMKO WP0156 Substitutes
Water Pump, engine cooling
Trade numbers : WP0156
Impeller Ø: 85,5mmOperating Mode: MechanicalWater Pump Type: for v-ribbed belt use
Schaeffler FAG 772 0127 30 Substitutes
Bellow Kit, drive shaft
Inner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: NBR (nitrile butadiene rubber)Thread Size: M20x1,5
SPIDAN 26217 Substitutes
Bellow Kit, drive shaft
Bellows Material: NBR (nitrile butadiene rubber)Height: 103mmInner Diameter 1: 22mmInner Diameter 2: 78mmSupplementary Article/Info 2: with nutThread Size: M22x1.5
SRLine S10-371 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: SteelWater Pump Type: for v-ribbed belt use
Stark SKCO-0070033 Substitutes
Ignition Coil
Coil Ignition System: Full Electronic Ignition (FI)Ignition Coil: Flush-Fitting Pencil Ignition CoilsIgnition Coil: incl. spark plug connectorNumber of mounting bores: 1Number of pins: 2-pin connectorOperating Voltage: 12V
STELLOX 61-00014-SX Substitutes
Ignition Coil
Ignition Coil: Connector Type SAEIgnition Coil: incl. spark plug connectorNumber of connectors: 2Voltage: 12VWeight: 0,269kg
SWAG 50 90 3288 Substitutes
Bellow, drive shaft
Replaced numbers : 50 90 3172
Inner Diameter 1: 22mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,074kg
SWAG 50 90 3172 Substitutes
Bellow, drive shaft
Fitting Position: Front Axle LeftFitting Position: Front Axle RightFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,088kg
SWAG 50 93 1143 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,200kg
SWAG 60 90 9699 Substitutes
Cable Pull, clutch control
Inner Length: 234mmLeft-/right-hand drive vehicles: for left-hand drive vehiclesOuter Length: 975mmWeight: 0,2kg
SWAG 40 90 2717 Substitutes
Bellow Kit, drive shaft
Fitting Position: Front AxleFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,209kg
SWAG 10 92 8489 Substitutes
Sensor, washer fluid level
Length: 88,62mmOuter Diameter: 15,79mmWeight: 0,016kg
SWAG 33 10 3844 Substitutes
Water Pump, engine cooling
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
TOPRAN 302 726 Substitutes
Ignition Coil
Trade numbers : 302 726 001
Ignition Coil: Connector Type SAEIgnition Coil: Flush-Fitting Pencil Ignition CoilsIgnition Coil: incl. spark plug connectorNumber of pins: 2-pin connectorSupplementary Article/Info 2: Do not fit parts from different manufacturers!
TOPRAN 301 253 Substitutes
Bellow Kit, drive shaft
Trade numbers : 301 253 001
Bellows Material: RubberHeight: 103mmInner Diameter 1: 20mmInner Diameter 2: 78mm
VAICO V25-0394 Substitutes
Bellow Kit, drive shaft
Fitting Position: Front AxleFitting Position: transmission sidedFitting Position: Wheel SideMaterial: RubberWeight: 0,128kg
VALEO 245249 Substitutes
Ignition Coil
Ignition Coil: Flush-Fitting Pencil Ignition CoilsNumber of pins: 2-pin connector
WALKER 17576 Substitutes
Exhaust Pipe
Code Letter: 62Length: 680mmSupplementary Article/Info 2: without mounting partsWarranty: 3 years warrantyWeight: 3,020kg
WILMINK GROUP WG1496637 Substitutes
Ignition Coil
Alternative Repair Kit: WG1496636Number of pins: 2-pin connectorWeight: 0,2kg
WILMINK GROUP WG1236781 Substitutes
Water Pump, engine cooling
Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
WILMINK GROUP WG1498178 Substitutes
Ignition Coil
Ignition Coil: Connector Type SAENumber of pins: 2-pin connectorPlug Type: FemaleVoltage: 12V
WILMINK GROUP WG1054738 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,200kg
WILMINK GROUP WG1790111 Substitutes
Water Pump, engine cooling
Impeller Ø: 66mmNumber of blades/vanes: 6Operating Mode: MechanicalSupplementary Article/Supplementary Info: with sealWater pump impeller material: MetalWater Pump Type: for v-ribbed belt use
WILMINK GROUP WG1012306 Substitutes
Ignition Coil
for article number: 8010479Number of pins: 2-pin connector
WILMINK GROUP WG1487451 Substitutes
Ignition Coil
Trade numbers : 0 040 100 408, E2019100408A1
Connector type: Spark SpringNumber of connectors: 1Number of pins: 2-pin connectorVoltage: 12V
WILMINK GROUP WG2220971 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,260kg
WILMINK GROUP WG2225267 Substitutes
Water Pump, engine cooling
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
WILMINK GROUP WG2220539 Substitutes
Water Pump, engine cooling
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
WILMINK GROUP WG1237250 Substitutes
Water Pump, engine cooling
Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Supplementary Info: with seal
WILMINK GROUP WG1905306 Substitutes
Ignition Coil
for article number: 8010479ENumber of pins: 2-pin connectorQuality: OE EQUIVALENT
WILMINK GROUP WG1789968 Substitutes
Water Pump, engine cooling
Impeller Ø: 64,8mmNumber of blades/vanes: 8Number of Teeth: 21Operating Mode: MechanicalSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWater Pump Pulley Ø: 62,3mmWater Pump Type: for timing belt drive
WILMINK GROUP WG1446140 Substitutes
Ignition Coil
Ignition Coil: Flush-Fitting Pencil Ignition CoilsNumber of pins: 2-pin connector
WILMINK GROUP WG2009257 Substitutes
Ignition Coil
Connector type: Spark SpringNumber of connectors: 1Number of pins: 2-pin connectorPackaging height: 10cmPackaging length: 19,5cmPackaging width: 8cmPacking Type: BoxSupplementary Article/Info 2: without electronicsVoltage: 12V
WILMINK GROUP WG1439701 Substitutes
Ignition Coil
for OE number: 1 578 771Number of connectors: 2Weight: 0,200kg
WILMINK GROUP WG2228348 Substitutes
Water Pump, engine cooling
Material: Cast AluminiumNumber of blades/vanes: 6Seal Material: RubberSupplementary Article/Info 2: with seal ringWater pump impeller material: MetalWeight: 0,648kg
Wti Automotive C901268 Substitutes
Cable Pull, clutch control
Inner Length: 234mmOuter Length: 975mmWeight: 0,2kg
Wti Automotive C901136 Substitutes
Cable Pull, clutch control
Inner Length: 234mmOuter Length: 975mmWeight: 0,2kg
Wti Automotive B832055 Substitutes
Bellow, drive shaft
Fitting Position: Front AxleFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,209kg
Wti Automotive A221017 Substitutes
Bellow, drive shaft
Fitting Position: Front AxleFitting Position: transmission sidedInner Diameter 1: 20mmInner Diameter 2: 78mmLength: 103mmMaterial: RubberWeight: 0,088kg